Tampers and Events

Magnetic. Detects the presence of an external magnetic field.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

Magnetic. Detects the presence of an external magnetic field.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

No communication with the register.

The tilt detector has been activated, possibly as a result of physical tampering.

The meter has detected an external magnetic field.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT detects that consumption has dropped below the high flow threshold after being in a high flow state.

Note: If the ERT is in a high flow detected state and high flow detection is disabled, then this event is logged immediately.

A critical internal error has occurred that is not described by other events.

A rightsizing operation request for the ERT has been sent from the client.

The rightsizing operation is complete.

A rightsizing operation cancellation request for the ERT has been sent

from the client.A rightsizing operation cancellation request for the ERT has been sent

from the client.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The meter rightsizing parameters have been changed.

The key has been updated in the device.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A planned restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

No communication with the register.

The meter has detected an external magnetic field.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT has detected reverse flow.

Note: This is sometimes referred to as backflow.

The ERT has detected the end of reverse flow after having reported reverse flow.

Note: This is sometimes referred to as backflow.

The ERT detects that a remote disconnect valve is attached and is working properly. The event is triggered when the state was previously unknown or previously not working properly.

The ERT detects a remote disconnect valve is attached but it is not working properly.

The meter detects consumption has exceeded the high flow threshold.

The meter detects that consumption has dropped below the high flow threshold after having been in a high flow state.

The device detects that the temperature has exceeded the high temperature threshold.

The device detects that the temperature has dropped below the high temperature threshold after having been in a high temperature state.

The device detects air in the meter, possibly due to the meter being removed from the installation.

The device no longer detects air in the meter.

A critical internal error has occurred that is not described by other events.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The key has been updated in the device.

The application has not received any incoming data, which indicates that the device may not be communicating on the network.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

The meter has entered prover mode.

The meter has existed prover mode.

The valve is in a disconnected state but flow has been detected by the device.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged one time every 24 hours.

The meter's push button has been depressed causing the LCD to turn on.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged one time every 24 hours.

The device has detected that its flow sensor has failedd. An ultrasonic measurement unit (UMU) hard error. This is an unrecoverable error.

The device has detected that the flow is outside the physical range of the measurement sensor. Qmin or Qmax exceeded.

The device has detected that the flow has returned to a level within the physical range of the measurement sensor after having been outside the range.

The device has detected that the gas temperature is outside the range of the temperature sensor (temperature max exceeded, temperature min

exceeded).

The device has detected that the gas temperature has returned to a value within the range of the temperature sensor after having been outside the range.

The device has detected that a flow sensor measurement error has occurred. This is an unrecoverable error.

The device has detected that its ultrasonic transducers have an issue which is reflected by an abnormal gain or an abnormal Tup/Tdown (time required by the ultrasonic signal from the emitter to the receiver). This is an unrecoverable error.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A planned restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was received but failed to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The disconnect command was received and has completed. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The valve actuation threshold has been exceeded. This will trigger at a count of 76 actuations for the Intelis Gas meter.

An override operation has occurredd for this valve.

An auto disconnect occurred in the meter.

A change has been made to the Prover Mode Maximum Time setting.

A change has been made to the High Flow Sampling Configuation setting.

A change has been made to the High Temperature Event Configuration Setting.

The High Flow Disconnect Enable configuration setting has changed.

The high temperature automatic disconnect configuration setting has changed.

The air in pipe automatic disconnect configuration setting has changed.

This event occurs with an application-level security failure for access control.

A change has been made to the Prover Mode Pulse Width setting.

A change has been made to the Prover Mode Pulse Weight setting.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

The device has detected that its index value(s) may have become corrupted. The device should be replaced.

A change has been made to the Intelis Gas Meter's UMU calibration A2 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B1 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B2 value. This event is added to the log when the calibration completes.

No communication with the register.

The meter has detected an external magnetic field.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT has detected reverse flow.

Note: This is sometimes referred to as backflow.

The ERT has detected the end of reverse flow after having reported reverse flow.

Note: This is sometimes referred to as backflow.

The ERT detects that a remote disconnect valve is attached and is working properly. The event is triggered when the state was previously unknown or previously not working properly.

The ERT detects a remote disconnect valve is attached but it is not working properly.

The meter detects consumption has exceeded the high flow threshold.

The meter detects that consumption has dropped below the high flow threshold after having been in a high flow state.

The device detects that the temperature has exceeded the high temperature threshold.

The device detects that the temperature has dropped below the high temperature threshold after having been in a high temperature state.

The device detects air in the meter, possibly due to the meter being removed from the installation.

The device no longer detects air in the meter.

A critical internal error has occurred that is not described by other events.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The key has been updated in the device.

The application has not received any incoming data, which indicates that the device may not be communicating on the network.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

The meter has entered prover mode.

The meter has existed prover mode.

The valve is in a disconnected state but flow has been detected by the device.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged one time every 24 hours.

The meter's push button has been depressed causing the LCD to turn on.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged one time every 24 hours.

The device has detected that its flow sensor has failedd. An ultrasonic measurement unit (UMU) hard error. This is an unrecoverable error.

The device has detected that the flow is outside the physical range of the measurement sensor. Qmin or Qmax exceeded.

The device has detected that the flow has returned to a level within the physical range of the measurement sensor after having been outside the range.

The device has detected that the gas temperature is outside the range of the temperature sensor (temperature max exceeded, temperature min

exceeded).

The device has detected that the gas temperature has returned to a value within the range of the temperature sensor after having been outside the range.

The device has detected that a flow sensor measurement error has occurred. This is an unrecoverable error.

The device has detected that its ultrasonic transducers have an issue whichis reflected by an abnormal gain or an abnormal Tup/Tdown (time required by the ultrasonic signal from the emitter to the receiver). This is an unrecoverable error.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A plannedd restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was receivedd but failedd to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The disconnect command was received and has completed. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The valve actuation threshold has been exceeded. This will trigger at a count of 76 actuations for the Intelis Gas meter.

An override operation has occurredd for this valve.

An auto disconnect occurred in the meter.

A change has been made to the Prover Mode Maximum Time setting.

A change has been made to the High Flow Sampling Configuation setting.

A change has been made to the High Temperature Event Configuration Setting.

The High Flow Disconnect Enable configuration setting has changed.

The high temperature automatic disconnect configuration setting has changed.

The air in pipe automatic disconnect configuration setting has changed.

This event occurs with an application-level security failure for access control.

A change has been made to the Prover Mode Pulse Width setting.

A change has been made to the Prover Mode Pulse Weight setting.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

The device has detected that its index value(s) may have become corrupted. The device should be replaced.

A change has been made to the Intelis Gas Meter's UMU calibration A2 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B1 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B2 value. This event is added to the log when the calibration completes.

No communication with the register.

The tilt detector has been activated, possibly as a result of physical tampering.

The meter has detected an external magnetic field.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT detects that consumption has dropped below the high flow threshold after being in a high flow state.

Note: If the ERT is in a high flow detected state and high flow detection is disabled, then this event is logged immediately.

The device has detected that the encoder micros has reset unexpectedly.

Remote-mount Itron Cellular 500G Modules only.

A critical internal error has occurred that is not described by other events.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The key has been updated in the device.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

A configuration change requiring legally relevant logging is requested and failed because the Legally Relevant Log is full.

The Fixed Network Connection Check Enable (attribute 2) has changed.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A planned restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

A change has been made to the High Flow Event Configuration.

The EDHOC process has been initiated.

An error occurred during the EDHOC process.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

The tilt detector has been activated, possibly as a result of physical tampering.

The meter has detected an external magnetic field.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

A physical cut cable has been detected by the ERT.

A physical cut cable is no longer detected by the ERT.

A critical internal error has occurred that is not described by other events.

A rightsizing operation request for the ERT has been sent from the client.

The rightsizing operation is complete.

A rightsizing operation cancellation request for the ERT has been sent from the client. A rightsizing operation cancellation request for the ERT has been sent from the client.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The meter rightsizing parameters have been changed.

The key has been updated in the device.

The application has not received any incoming data, which indicates that the device may not be communicating on the network.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A planned restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

No communication with the register.

The meter has detected an external magnetic field.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT has detected reverse flow.

Note: This is sometimes referred to as backflow.

The ERT has detected the end of reverse flow after having reported reverse flow.

Note: This is sometimes referred to as backflow.

The ERT detects that a remote disconnect valve is attached and is working properly. The event is triggered when the state was previously unknown or previously not working properly.

The ERT detects a remote disconnect valve is attached but it is not working properly.

The meter detects consumption has exceeded the high flow threshold.

The meter detects that consumption has dropped below the high flow threshold after having been in a high flow state.

The device detects that the temperature has exceeded the high temperature threshold.

The device detects that the temperature has dropped below the high temperature threshold after having been in a high temperature state.

The device detects air in the meter, possibly due to the meter being removed from the installation.

The device no longer detects air in the meter.

The meter detects that the micro has reset unexpectedly. The meter must be replaced.

The meter detects the gas pressure has exceeded the high pressure threshold.

The meter detects the gas pressure has dropped below the high pressure threshold after it was detected to be in a high pressure state.

The meter detects the gas pressure has fallen below the low pressure threshold.

The meter detects the gas pressure has risen above the low pressure threshold after it was detected to be in a low pressure state.

The meter detects the gas gauge pressure has exceeded the pressure tamper threshold.

The meter detects the gas gauge pressure has dropped below the pressure tamper threshold after it was detected to be in a pressure tamper state.

A critical internal error has occurred that is not described by other events.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The key has been updated in the device.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

The meter has entered prover mode.

The meter has existed prover mode.

The valve is in a disconnected state but flow has been detected by the device.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged one time every 24 hours.

The meter's push button has been depressed causing the LCD to turn on.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged one time every 24 hours.

The device has detected that its flow sensor has failedd. An ultrasonic measurement unit (UMU) hard error. This is an unrecoverable error.

The device has detected that the flow is outside the physical range of the measurement sensor. Qmin or Qmax exceeded.

The device has detected that the flow has returned to a level within the physical range of the measurement sensor after having been outside the range.

The device has detected that the gas temperature is outside the range of the temperature sensor (temperature max exceeded, temperature min

exceeded).

The device has detected that the gas temperature has returned to a value within the range of the temperature sensor after having been outside the range.

The device has detected that a flow sensor measurement error has occurred. This is an unrecoverable error.

The device has detected that its ultrasonic transducers have an issue whichis reflected by an abnormal gain or an abnormal Tup/Tdown (time required by the ultrasonic signal from the emitter to the receiver). This is an unrecoverable error.

The meter's EFC current state has changed or the meter's parent in the Neighborhood MAC Address array has changed.

The Legally Relevant Log is full and a configuration change occurred that requires logging to the Legally Relevant Log. The configuration change log failed.

The meter index has detected an unexpected UMU CRC. This may occur when the UMU fails to calculate its CRC at boot. The error can usually be resolved by causing a reset of the UMU.

The UMU CRC has returned to an expected value after an unexpected value had been detected.

The meter detected that its gas pressure sensor has encountered an unrecoverable failure. The meter's LCD alarm menu should present the failure as fatal. The meter (including the UMU) must be replaced. Event details provide more information on the cause of the failure.

The valve is likely in a Closed state and the meter no longer detects flow after having detected flow and triggering event 532 (Flow while disconnected).

The meter detected that its barometric pressure sensor encountered an unrecoverable failure. The meter's LCD alarm menu should present the failure as fatal. The meter's index must be replaced.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

The DST calendar has reached its end. A new DST calendar must be downloaded

A new configuration has been downloaded.

A watchdog error. Reboot.

A plannedd restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was receivedd but failedd to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The disconnect command was received and has completed. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The valve actuation threshold has been exceeded. This will trigger at a count of 76 actuations for the Intelis Gas meter.

An override operation has occurredd for this valve.

An auto disconnect occurred in the meter.

A change has been made to the Prover Mode Maximum Time setting.

A change has been made to the High Flow Sampling Configuation setting.

A change has been made to the High Temperature Event Configuration Setting.

The High Flow Disconnect Enable configuration setting has changed.

The high temperature automatic disconnect configuration setting has changed.

A change has been made to the Prover Mode Pulse Width setting.

A change has been made to the Prover Mode Pulse Weight setting.

A change has been made to one of the DHCP address indexes.

A change has been made to the High Flow Event configuration threshold.

The High Pressure Disconnect Enable configuration has changed.

The Low Pressure Disconnect Enable configuration has changed.

The Factory High Flow Disconnect Enable configuration has changed.

A change has been made to the High Pressure Event configuration.

A change has been made to the Low Pressure Event configuration.

A change has been made to the Pressure Tamper Event configuration.

A change has been made to the Pressure and Temperature Profile.

A mismatch has been detected between the pressure sensing capabilities of the index and meter body. This occurs if the index supports pressure sensing but the meter body does not, or if the meter body supports pressure sensing but the index does not.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for rollover count changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

The meter has detected that the configuration of the flow sensor has changed.

The meter has been sealed.

The meter has been unsealed.

The device has detected that its index value(s) may have become corrupted. The device should be replaced.

A change has been made to the Intelis Gas Meter's UMU calibration A2 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B1 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B2 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B3 value. This event is added to the log when the calibration completes.

A change has been made to the meter's display units.

Cable Cut. The ERT detects a cut or break in the cable. This counter value increases by 1 when an event occurs and then latches. Latch state is cleared when the ERT is read.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

Cable Cut. Not supported and should be ignored if changes are seen.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

Cable Cut. The cable is not accessible. However, the cable tamper/event functions the same as the Remote (3-wire). The ERT detects a cut or break in the cable. This counter value increases by 1 when an event occurs and then latches. Latch state is cleared when the ERT is read.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

Cable Cut. The ERT detects a cut or break in the cable. This counter value increases by 1 when an event occurs.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

Cable Cut. Not supported and should be ignored if changes are seen.

Tilt. Detects a tilt of greater than 60 degrees occurred for more than 0.5 seconds.

Leak Detection/Reverse Flow. Indicates that both Leak Detection and Reverse Flow conditions exist. The indicator changes when one condition no longer exists and resets to zero when both conditions no longer exist.

Cable Cut. Detects a cut or break in the cable.

There is a corrupt digit in the encoded register reading.

No communication with the register.

The register is not sending a valid read.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT has detected continuous flow over a set period of time.

The ERT has detected the end of continuous flow after having reported a leak.

The ERT has detected reverse flow.

Note: This is sometimes referred to as backflow.

The ERT has detected the end of reverse flow after having reported reverse flow.

Note: This is sometimes referred to as backflow.

The ERT detects a leak sensor attached and it is working properly. The event is triggered when the state was previously unknown or was previously not working properly.

The ERT detects a leak sensor is attached, but it is not working properly.

The ERT does not detect that a leak sensor is attached after previously having one attached.

The ERT detects that a remote disconnect valve is attached and is working properly. The event is triggered when the state was previously unknown or previously not working properly.

The ERT ddetects a remote disconnect valve is attached but it is not working properly.

The ERT has detected an internal pulse mismatch.

A physical cut cable has been detectedd by the ERT.

A physical cut cable is no longer detected by the ERT.

The ERT detects consumption has exceeded the high flow threshold.

The ERT detects consumption has dropped below the high flow threshold after having been in a high flow state.

Note: If the device is in a high flow detected state, and high flow detection is disabled then this event should be logged immediately.

A critical internal error has occurred that is not described by other events.

The client has requested a rightsizing operating in the ERT.

The rightsizing operation is complete.

The rightsizing operation was canceled.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

Meter rightsizing parameters have been changed.

The key has been updated in the device.

The application has not received any incoming data, which indicates that the device may not be communicating on the network.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The ddevice has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

Badger extended alarm: bit 0 = register removal.

Badger extended alarm: bit 1 = temperature alarm.

Badger extended alarm: bit 2 = end of life alarm.

Badger extended alarm: bit 3 = no usage alarm.

Badger extended alarm: bit 4 = reverse flow alarm.

Badger extended alarm: bit 5 = leak alarm.

Badger extended alarm: bit 6 = program alarm.

Badger extended alarm: bit 7 = tamper.

Kamstrup extended alarm byte 1: bit 0 = active reverse flow.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 1 = historic reverse.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm byte 1: bit 2 = active dry.

The meter is in a current empty pipe state.

Debounce every 24 hours.

Kamstrup extended alarm: Kamstrup extended alarm byte 1: bit 3 = historic dry.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm byte 1: bit 4 = active burst.

The meter is currently in a high flow state outsidde of the meter parameters.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 5 = historic burst.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm: byte 1: bit 6 = the encoder setup has been changed one or more times since production.

Kamstrup extended alarm byte 1: bit 7 = the meter is in an active leak state.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 8 = historic leak.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm: The minimum meter temperature detected. This alarm is sent when the temperature on the Kamstrup meter is lower than 36° F.

Kamstrup extended alarm: The maximum meter temperature has been detected. This alarm is sent when the temperature on the Kamstrup meter is higher than 125° F.

Kamstrup extended alarm: The meter has detected no usage.

Sensus Intelis Water Meter extended alarm: Th meter's backflow consumption register indicates a total backflow that is outside of the threshold values for expected backflow.

Sensus Intelis Water Meter extended alarm: The device detects that the pipe is empty, possibly due to the meter being removed from the installation.

Sensus Intelis Water Meter extended alarm: The meter has detected that it has been installed in a reverse orientation.

Sensus Intelis Water Meter extended alarm: The meter's battery life has less than six months (for the NAM meter) or 12 months (for the international meter) remaining.

Sensus Intelis Water Meter extended alarm: The meter has detected a leak.

The average flow rate during each of the hours over the past day (for NAM meter) or over a configured number of days (for international meter)was above the leakage flow rate threshold.

This event clears when the average flow rate for one hour returns to within the configured threshold.

Sensus Intelis Water Meter extended alarm: The meter has detected a burst flow alarm which can indicate a broken pipe.

Sensus Intelis Water Meter extended alarm: The meter has detected that the cover was opened. This can indicate that the meter has been tampered with.

Sensus Intelis Water Meter extended alarm: The meter has detected a temperature alarm. The meter has reached a temperature that is outside of the temperature range.

This event clears after the alarm duration time passes (one day minimum).

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A plannedd restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was received but failed to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The disconnect command was received and has completed. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

A restrict/service limit event was received and has been completed. The event detail will contain the verbose-result attribute of the DisconnectControl object.

A restrict/service limit was received but failed to execute. The event detail will contain the verbose-result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for count sample configuration debounce changed.

The metrology parameter for encoder driver type changed.

The metrology parameter for prescaler changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

The metrology parameter for count sample configuration sample width parameters changed.

There is a corrupt digit in the encoded register reading.

No communication with the register.

The register is not sending a valid read.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT has detected continuous flow over a set period of time.

The ERT has detected the end of continuous flow after having reported a leak.

The ERT has detected reverse flow.

Note: This is sometimes referred to as backflow.

The ERT has detected the end of reverse flow after having reported reverse flow.

Note: This is sometimes referred to as backflow.

The ERT detects a leak sensor attached and it is working properly. The event is triggered when the state was previously unknown or was previously not working properly.

The ERT detects a leak sensor is attached, but it is not working properly.

The ERT does not detect that a leak sensor is attached after previously having one attached.

The ERT detects that a remote disconnect valve is attached and is working properly. The event is triggered when the state was previously unknown or previously not working properly.

The ERT detects a remote disconnect valve is attached but it is not working properly.

The ERT has detected an internal pulse mismatch.

A physical cut cable has been detected by the ERT.

A physical cut cable is no longer detected by the ERT.

The ERT detects consumption has exceeded the high flow threshold.

The ERT detects consumption has dropped below the high flow threshold after having been in a high flow state.

The ERT detects an encoder microprocessor reset.

Remote-mount Itron Cellular 500W Modules only.

A critical internal error has occurred that is not described by other events.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

The key has been updated in the device.

The load profile object has been cleared.

The time has been changed manually.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

The ERT received a corrupt data character from the meter. This event is logged a maximum of one time per day.

This event is not logged if the corrupt data character is received as part of the volume or consumption field.

The Fixed Network Connection Check Enable attribute has changed.

Badger extended alarm: bit 0 = register removal.

Badger extended alarm: bit 1 = temperature alarm.

Badger extended alarm: bit 2 = end of life alarm.

Badger extended alarm: bit 3 = no usage alarm.

Badger extended alarm: bit 4 = reverse flow alarm.

Badger extended alarm: bit 5 = leak alarm.

Badger extended alarm: bit 6 = program alarm.

Badger extended alarm: bit 7 = tamper.

Kamstrup extended alarm byte 1: bit 0 = active reverse flow.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 1 = historic reverse.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm byte 1: bit 2 = active dry.

The meter is in a current empty pipe state.

Debounce every 24 hours.

Kamstrup extended alarm: Kamstrup extended alarm byte 1: bit 3 = historic dry.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm byte 1: bit 4 = active burst.

The meter is currently in a high flow state outsidde of the meter parameters.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 5 = historic burst.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm: byte 1: bit 6 = the encoder setup has been changed one or more times since production.

Kamstrup extended alarm byte 1: bit 7 = the meter is in an active leak state.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 8 = historic leak.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm: The minimum meter temperature detected. This alarm is sent when the temperature on the Kamstrup meter is lower than 36° F.

Kamstrup extended alarm: The maximum meter temperature has been detected. This alarm is sent when the temperature on the Kamstrup meter is higher than 125° F.

Kamstrup extended alarm: The meter has detected no usage.

Sensus Intelis Water Meter extended alarm: Th meter's backflow consumption register indicates a total backflow that is outside of the threshold values for expected backflow.

Sensus Intelis Water Meter extended alarm: The device detects that the pipe is empty, possibly due to the meter being removed from the installation.

Sensus Intelis Water Meter extended alarm: The meter has detected that it has been installed in a reverse orientation.

Sensus Intelis Water Meter extended alarm: The meter's battery life has less than six months (for the NAM meter) or 12 months (for the international meter) remaining.

Sensus Intelis Water Meter extended alarm: The meter has detected a leak.

The average flow rate during each of the hours over the past day (for NAM meter) or over a configured number of days (for international meter)was above the leakage flow rate threshold.

This event clears when the average flow rate for one hour returns to within the configured threshold.

Sensus Intelis Water Meter extended alarm: The meter has detected a burst flow alarm which can indicate a broken pipe.

Sensus Intelis Water Meter extended alarm: The meter has detected that the cover was opened. This can indicate that the meter has been tampered with.

Sensus Intelis Water Meter extended alarm: The meter has detected a temperature alarm. The meter has reached a temperature that is outside of the temperature range.

This event clears after the alarm duration time passes (one day minimum).

Diehl Hydrus Meter extended alarm: The meter has detected air in the supply system and water flow rate measurement is not possible.

Diehl Hydrus Meter extended alarm: The meter has detected leakage above threshold for 24 consecutive hours. The alarm is reset 15 minutes after consumption is below the leakage threshold.

Diehl Hydrus Meter extended alarm: The meter has detected that flash or RAM is corrupted or manipulated. This is a fatal error, the meter must be replaced. This error is cleared three days after it is raised.

Diehl Hydrus Meter extended alarm: The meter has encountered a temperature measurement error. They median temperature is too low or too high (22° F / 212° F, -30° C/ 100° C), or, the cable temperature sensor is cut or disconnected.

Diehl Hydrus Meter extended alarm: The meter's ultrasonic hardware has encountered an error. The ultrasonic transducer is defective or short-circuited, or the ultrasonic transducer cable is cut or disconnected.

Diehl Hydrus Meter extended alarm: The meter is experiencing too much communication on its DMEI or optical interface over a short period of time. When communication capacity reaches zero (0) bytes, communication is temporarily paused. When communication capacity reaches below the minimum threshold (500 bytes is the default), then communications resume again.

Diehl Hydrus Meter extended alarm: The meter detects that flow is over the undersized meter threshold for one minute. The error is cleared after the detects flow that is under the undersized meter threshold for one minute.

Diehl Hydrus Meter extended alarm: A hardware temperature error is detected for one minute. The temperature cable is damaged or cut. After three days of no hardware temperature error detected, the meter clears the alarm.

Diehl Hydrus Meter extended alarm: The meter detects that consumption is below its configured limit. The 1.3 meter and the 2.0 meter versions reset this alarm after different consumption conditions are met.

Diehl Hydrus Meter extended alarm: The meter detects consumption below the no usage threshold for 30 days. The alarm is active one time ever 30 days. The alarm is cleared after consumption above the no usage threshold is measured for 15 minutes.

Diehl Hydrus Meter extended alarm: The meter has detected seven consecutive days of measurements disturbed by influences of cavitation, air water mixture, heavy electromagnetic, or heavy mechanic interferences (vibration). These interferences can be caused by pumps or other heavy equipment operating near the meter. After three days of no disturbed measurements, the meter clears the alarm.

Diehl Hydrus Meter extended alarm: The meter detected the temperature is lower than 3° C after four consecutive temperature measurements and the meter detects an Err4 at the same time. The meter resets the alarm after 30 days if the issue is resolved.

Diehl Hydrus Meter extended alarm: The meter detected an active Err7. The meter resets the alarm after 30 days without air detected in the pipe.

Diehl Hydrus Meter (version 2.0 only) extended alarm: The meter detects flow that is above the undersized meter threshold for 30 consecutive minutes. When the meter detects flow below the threshold for one minute, it resets the alarm.

Diehl Hydrus Meter extended alarm: The meter detects the calculated battery life is fewer than 400 days. The meter resets the alarm when the calculated battery life is more than 400 days.

Diehl Hydrus Meter extended alarm: The meter detects the medium temperature is hotter than 90° C for 60 consecutive minutes. The meter resets the alarm after medium temperature is 90° C or cooler for 60 consecutive minutes.

Diehl Hydrus Meter extended alarm: The meter detects a significant deviation between measurements of the two measuring paths. The meter resets the alarm three days after the deviation of measurements between the two paths goes a way.

Diehl Hydrus Meter extended alarm: The meter detects an entry into the metrological log.The ERT logs this event only one time and logs it again only if the meter alarm goes away and then reappears.

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A plannedd restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was received but failed to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The disconnect command was received and has completed. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

A restrict/service limit event was received and has been completed. The event detail will contain the verbose-result attribute of the DisconnectControl object.

A restrict/service limit was received but failed to execute. The event detail will contain the verbose-result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

A change was made to the High Flow Event Configuration threshold.

The EDHOC process has been initiated.

An error occurred during the EDHOC process.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for count sample configuration debounce changed.

The metrology parameter for encoder driver type changed.

The metrology parameter for prescaler changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

The metrology parameter for count sample configuration sample width parameters changed.

There is a corrupt digit in the encoded register reading.

No communication with the register.

The register is not sending a valid read.

The ERT module has a low battery warning. Just 10% of the battery's life remains.

The ERT has detected continuous flow over a set period of time.

The ERT has detected the end of continuous flow after having reported a leak.

The ERT has detected reverse flow.

Note: This is sometimes referred to as backflow.

The ERT has detected the end of reverse flow after having reported reverse flow.

Note: This is sometimes referred to as backflow.

The ERT detects a leak sensor attached and it is working properly. The event is triggered when the state was previously unknown or was previously not working properly.

The ERT detects a leak sensor is attached, but it is not working properly.

The ERT does not detect that a leak sensor is attached after previously having one attached.

The ERT detects that a remote disconnect valve is attached and is working properly. The event is triggered when the state was previously unknown or previously not working properly.

The ERT ddetects a remote disconnect valve is attached but it is not working properly.

The ERT has detected an internal pulse mismatch.

A physical cut cable has been detectedd by the ERT.

A physical cut cable is no longer detected by the ERT.

The ERT detects consumption has exceeded the high flow threshold.

The ERT detects consumption has droppedd below the high flow threshold after having been in a high flow state.

A critical internal error has occurred that is not described by other events.

The client has requested a rightsizing operating in the ERT.

The rightsizing operation is complete.

The rightsizing operation was canceled.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva Network Mode.

Any change to the Battery Use Parameters structure results in this event.

Meter rightsizing parameters have been changed.

The key has been updated in the device.

The application has not received any incoming data, which indicates that the device may not be communicating on the network.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A Time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The ddevice has been changed from OpenWay Riva Network Mode to ChoiceConnect 100-series Mobile Mode.

Badger extended alarm: bit 0 = register removal.

Badger extended alarm: bit 1 = temperature alarm.

Badger extended alarm: bit 2 = end of life alarm.

Badger extended alarm: bit 3 = no usage alarm.

Badger extended alarm: bit 4 = reverse flow alarm.

Badger extended alarm: bit 5 = leak alarm.

Badger extended alarm: bit 6 = program alarm.

Badger extended alarm: bit 7 = tamper.

Kamstrup extended alarm byte 1: bit 0 = active reverse flow.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 1 = historic reverse.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm byte 1: bit 2 = active dry.

The meter is in a current empty pipe state.

Debounce every 24 hours.

Kamstrup extended alarm: Kamstrup extended alarm byte 1: bit 3 = historic dry.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm byte 1: bit 4 = active burst.

The meter is currently in a high flow state outsidde of the meter parameters.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 5 = historic burst.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm: byte 1: bit 6 = the encoder setup has been changed one or more times since production.

Kamstrup extended alarm byte 1: bit 7 = the meter is in an active leak state.

Debounce every 24 hours.

Kamstrup extended alarm byte 1: bit 8 = historic leak.

The active info-code within the last 30 days, no matter how long the info-code was active.

Debounce every 30 days.

Kamstrup extended alarm: The minimum meter temperature detected. This alarm is sent when the temperature on the Kamstrup meter is lower than 36° F.

Kamstrup extended alarm: The maximum meter temperature has been detected. This alarm is sent when the temperature on the Kamstrup meter is higher than 125° F.

Kamstrup extended alarm: The meter has detected no usage.

Sensus Intelis Water Meter extended alarm: Th meter's backflow consumption register indicates a total backflow that is outside of the threshold values for expected backflow.

Sensus Intelis Water Meter extended alarm: The device detects that the pipe is empty, possibly due to the meter being removed from the installation.

Sensus Intelis Water Meter extended alarm: The meter has detected that it has been installed in a reverse orientation.

Sensus Intelis Water Meter extended alarm: The meter's battery life has less than six months (for the NAM meter) or 12 months (for the international meter) remaining.

Sensus Intelis Water Meter extended alarm: The meter has detected a leak.

The average flow rate during each of the hours over the past day (for NAM meter) or over a configured number of days (for international meter)was above the leakage flow rate threshold.

This event clears when the average flow rate for one hour returns to within the configured threshold.

Sensus Intelis Water Meter extended alarm: The meter has detected a burst flow alarm which can indicate a broken pipe.

Sensus Intelis Water Meter extended alarm: The meter has detected that the cover was opened. This can indicate that the meter has been tampered with.

Sensus Intelis Water Meter extended alarm: The meter has detected a temperature alarm. The meter has reached a temperature that is outside of the temperature range.

This event clears after the alarm duration time passes (one day minimum).

The OpenWay Collections Manager (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A plannedd restart of the ERT (for example, after a firmware download completes).

The ERT was unable to adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was receivedd but failedd to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The disconnect command was received and has completed. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

A restrict/service limit event was received and has been completed. The event detail will contain the verbose-result attribute of the DisconnectControl object.

A restrict/service limit was received but failed to execute. The event detail will contain the verbose-result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application-level security failure for certificates.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application-level security failure for replays.

A signed authorization was issued to "Itron-RMA" has been received.

The metrology parameter for pressure compensation (PCOMP) changed.

The metrology parameter for count rate changed.

The metrology parameter for rollover count changed.

The metrology parameter for count sample configuration debounce changed.

The metrology parameter for encoder driver type changed.

The metrology parameter for prescaler changed.

The metrology parameter for initial index changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has started.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change was made to the CompressedLoadProfile object capture_period.

The metrology parameter for count sample configuration sample width parameters changed.